- All products
- Butyls & bitumens
- Single sided
- Conformable Aluminum Butyl Tape
- Single sided
Conformable Butyl Tape for Roofs
ATyT’s waterproof butyl tape is a self-adhesive solution designed for sealing and waterproofing roofs, roof coverings and building junctions. It consists of an aluminum foil with a RAL 8004 terracotta (tile-colored) finish, coated with butyl rubber adhesive and protected by a polypropylene (PP) liner that makes handling and placement easier.
Especially suited as a butyl tape for roofs, it reinforces the watertightness of joints, flashings and protruding roof elements. Its composition combines the waterproofing properties of butyl rubber with the protection of the aluminum backing, providing a solution that resists weather exposure and UV rays.
This waterproofing butyl tape comes in two versions, 2D and 3D, both with a total thickness of 1.1 mm. Although they share the same composition and declared technical values, they differ in the configuration of their aluminum backing and their ability to conform to different geometries.
The 2D aluminum butyl tape features an aluminum backing with a two-dimensional configuration, with small undulations. It is intended for sealing work on flat surfaces or surfaces with relatively simple geometry, such as longitudinal joints, straight flashings and roof junctions that do not require significant three-dimensional deformation.
The 3D aluminum butyl tape, on the other hand, has a three-dimensional finish that helps it conform to surfaces with relief and more complex shapes. This configuration is especially useful for waterproofing work on profiled tiles, irregular junctions and areas where the material must be molded to follow the geometry of the substrate.
Thanks to these characteristics, the conformable butyl tape in its 3D version makes it easier to treat the singular points of a roof, such as junctions between different planes, flashings around protruding elements and corrugated surfaces. The 2D version is an alternative for applications that require less complex conforming.
As a waterproof roofing strip, both versions allow sealing work to be done without the need for torch-on application systems. Their butyl rubber adhesive provides a direct bond to compatible surfaces, provided they are properly prepared and enough pressure is applied during installation.
The roof sealing tape offers high resistance to weather conditions and corrosion, thanks to its aluminum backing. The technical data sheets also state water impermeability and a product lifespan of ten years or more, under the conditions set out by the manufacturer.
In maintenance and repair work, the butyl tape for roof sealing can be used to reinforce joints, repair certain junctions on metal roofs and seal fixing points or penetrations. Its roll format makes it possible to cut the length needed and adapt the application to the dimensions of each job.
The butyl tape is especially useful at junctions between building elements, gutters, flashings and other areas where it is important to prevent water ingress. The choice between 2D and 3D makes it possible to match the finish of the tape to the complexity of the surface.
Thanks to its combination of waterproofing, environmental resistance and ease of installation, ATyT’s 2D and 3D aluminum butyl tapes are a solution for construction professionals, roof installers and maintenance companies that need to carry out sealing and leak protection work.
ADHESIVE PROPERTIES | VALUES |
Total thickness | 1.1 mm |
Adhesion to concrete | ≥ 2.94 N/cm2 |
Adhesion to steel | ≥ 147 N/cm2 |
Water permeability level | Impenetrable |
Product lifespan | ≥ 10 años |
Application temperature range | [-5ºC ~ +40ºC] |
Service temperature range | [-40ºC ~ +40ºC] |
Advantages That Make the Difference
- Self-adhesive waterproofing and sealing: the butyl rubber adhesive makes it possible to create bonds and seals on compatible surfaces without applying heat with a flame, making waterproofing work on roofs and coverings easier.
- Two finishes for different geometries: the 2D version is intended for flat surfaces and simple junctions, while the 3D version offers greater conformability to relief and complex shapes. This distinction makes it possible to select the most suitable configuration for the application.
- Resistance to weathering and UV rays: the aluminum backing provides protection against weather conditions and corrosion, allowing its use in compatible outdoor applications.
- High water impermeability: both versions are designed to reinforce the watertightness of joints, junctions and penetration points, providing a barrier against water ingress when correctly installed.
- Easy installation and tile-colored finish: the overlaid PP liner makes placement easier, while the RAL 8004 finish allows visual integration on roofs and roof coverings in similar tones.
Application Conditions
To ensure optimal tape performance:
- Check that the surface is clean, dry and free of dust, grease, oil and any substance that could impair adhesion.
- Check beforehand that the butyl rubber adhesive is compatible with the material it will be applied to.
- Install within the stated temperature range, between −5 °C and +40 °C.
- Select the 2D or 3D version according to the geometry and conforming needs of the surface.
- Cut the length needed to cover the joint, junction or sealing area.
- Remove the PP liner progressively during placement, avoiding unnecessary contact with the adhesive.
- Apply the tape to the prepared surface, trying to maintain even contact and avoid creases or areas without adhesion.
- Apply enough pressure over the entire surface to promote adhesion of the butyl rubber to the substrate.
- At irregular junctions, check that the tape conforms properly to the relief and that no lifted areas remain that could compromise watertightness.
Waterproofing the Junction Between a Chimney and a Roof with 3D Aluminum Butyl Tape
A company specializing in roof repair needed to improve the waterproofing of the junction between a chimney and a ceramic tile roof. The main challenge was to prevent water leaks in an area with different geometries, combining vertical surfaces with corrugated tiles.
After analyzing the application, ATyT recommended using the conformable 3D aluminum butyl tape, with butyl rubber adhesive and a RAL 8004 terracotta finish. Its three-dimensional configuration made it easier to conform to the relief of the tiles and the base of the chimney.
During installation, operators prepared the surfaces, progressively removed the liner and molded the butyl tape for roofs, applying pressure to achieve even contact.
The solution reinforced the watertightness of the junction without the need for a flame, offering simple application and a finish that blends in with the roof.
Frequently Asked Questions
Waterproof butyl tape is used to seal and waterproof joints, junctions and flashings on roofs and roof coverings. Its butyl rubber adhesive provides a self-adhesive bond, while the aluminum backing provides protection against environmental conditions and UV rays.
The main difference is the configuration of the aluminum backing. The 2D aluminum butyl tape is intended for flat surfaces and simple geometries, while the 3D aluminum butyl tape has a three-dimensional finish that makes it easier to conform to relief, undulations and more complex junctions. Both are 1.1 mm thick and share the declared technical values.
A conformable butyl tape is one that can be molded to fit the shape of the surface it is installed on. This is especially useful on roofs with corrugated tiles, changes of plane or protruding elements. The 3D version is intended for applications that require greater conformability.
Yes. Butyl tape for roofs is designed to reinforce the watertightness of joints, flashings, gutters and building junctions. Its combination of aluminum and butyl rubber makes it possible to create a barrier against water ingress, provided it is correctly installed on compatible surfaces.
Yes. The waterproofing butyl tape features an aluminum backing resistant to weather conditions and UV rays. The technical data sheets also state water impermeability, allowing it to be used in outdoor sealing and waterproofing applications.
Yes. This waterproof roofing strip can be used to reinforce the sealing of gutters, flashings, laps and roof edges. The choice between the 2D and 3D versions will depend on the geometry of the surface and the conforming needed during installation.
No. The roof sealing tape features a butyl rubber adhesive that allows direct application on compatible surfaces without the need for a flame. It is important to prepare the substrate properly and apply enough pressure to promote adhesion.
The butyl tape for roof sealing can be applied within the temperature range stated in the technical data sheet, between −5 °C and +40 °C. Its declared service temperature is between −40 °C and +40 °C. It is advisable to check the actual conditions of use before installation.
More than 1,500 customers have already placed their trust in ATyT.
Do you want to offer adhesive solutions that are up to the task of your projects?
Contact our technical team, and we’ll help you choose the adhesive tape that best suits your needs.